45™ HEAVY DUTY EJECTOR

879971007369 100005999

Utwardzana, obrabiana stal nierdzewna dla odporności na zużycie i pęknięcia

Zamiennik fabrycznego wyrzutnika jest precyzyjnie obrabiany z hartowanej stalowej blachy nierdzewnej 416 dla dodatkowej wytrzymałości i odporności na zużycie. Pomaga zapewnić pozytywne, spójne wyrzucanie łusek, z mniejszym ryzykiem problemów z niezawodnością spowodowanych zużytym lub złamanym wyrzutnikiem. Zawiera śrubę montażową ze stali nierdzewnej 416.

SPECYFIKACJE: Stal nierdzewna 416, naturalne wykończenie. Pasuje do pistoletów Ruger Mark I, Mark II, Mark III oraz 22/45.

Więcej...

Hardened, Machined Stainless Steel To Resist Wear & Breakage

Replacement for factory ejector is precision machined from hardened 416 stainless steel billet for extra strength and wear resistance. Helps ensure positive, consistent ejection, with reduced risk of reliability problems caused by a worn or broken ejector. Includes 416 stainless steel mounting screw.

SPECS: 416 stainless steel, natural finish. Fits Ruger Mark I, Mark II, Mark III, and 22/45 pistols.

Więcej...

Oceny klientów dla TACTICAL SOLUTIONS, LLC RUGER® .22 PISTOL EJECTOR

Liczba ocen: 5
Od brownells.com: 5
Średnia ocena: 3,4

Works great in my older MKI Bull barrel (17-10-2011)

Had to take my time removing loose rivet on the old ejector but the results were worth it.
Ejector fit great and required no modification.
I used a 4-40 SS socket head cap screw to install it.
I used a non-permanent thread locker product to hold the screw.
I also ordered the same manufacturers extractor kit which is as impressive as this part.
Both are working well after 500+ rounds.

Not a drop in part for a Mark II 22/45 (18-05-2015)

My Mark II 22/45 needed a new ejector as the original one has become loose and causing frequent malfunctions. I looked at this part thinking it would be convenient as a screw would be easier than dealing a rivet.

The new ejector looks exactly as pictured on the website. Unfortunately it is wider than the factory piece. This means it wouldn't sit flush against the bottom/inside of the upper which is round; preventing the screw from reaching the ejector (more on this later). I had to grind off the base of the ejector to allow it to sit flush against the upper.

Once that was done, I realized the mounting hole on the ejector didn't even line up to the hole on the upper. More grinding on the little tab fixed that. Now that everything looks good to go, I put a little dab of blue Loctite on the provided screw, and figured I was about done.

I reassembled the pistol and manually cycled the pistol to function test and realized the ejector was loose. Took the gun apart and realized the provided screw is too short and only several threads were screwed into the ejector. Just manually cycling the gun easily loosened the screw.

A trip to Home Depot I was able to source a longer stainless steel screw. It seems to cycle fine by hand although I haven't had a chance to actually shoot it and see if the ejection problems have been solved.

<img width="500" src='/userdocs/reviewimages/d13345c0-ecc2-40cb-a925-e49e28c9ef63.jpg' alt=''>

<img width="500" src='/userdocs/reviewimages/d0c20264-861b-46f3-9c51-ea2463fe7ce2.jpg' alt=''>

<img width="500" src='/userdocs/reviewimages/d64ea1f7-d77b-43f8-9bb5-19769840480c.jpg' alt=''>

Not an exact fit and screw too short (22-06-2015)

I tried to install on a Ruger Mark 2 Competition model. Found that the supplied screw just touches the ejector, so will not screw in. Need at least a 1/4 inch length screw. Also, the mounting hole on the ejector does not line up to the hole on the upper. Will required me to find an appropriate screw and some fitting. Emailed the manufacture, did not reply.

Well Made, but Screw too short. (13-07-2015)

Because I didn't want to pay shipping costs and possible repair costs to have a new Ejector installed on my Ruger MK II, I decided to try this for myself. I rec'd it quickly and noticed that in deed, it needed fitting. OK! I ground it down (dremel) to proper shape. Then noticed the screw is much too short! Another reviewer said, get 4-40 size screw (about 2 dollars from Lowes), which I did. I then ground the screw down to an appropriate length. (Screw can not extend through Ejector into the upper-receiver.) So over all, good ejector, and unless manufacturer updates the supplied screw to a longer length, you will need to buy a longer screw. Still glad I did this.

.22 ejctor (30-10-2017)

great ejector

Zobacz 5 dodatkowych opinii na brownells.com

234 234 1 PLN

Nr produktu: 100005999
TACTICAL SOLUTIONS, LLC RUGER® .22 PISTOL EJECTOR
Numer części: FP04X06 879971007369 Zamiennik fabrycznego wyrzutnika jest precyzyjnie obrabiany z hartowanej stalowej blachy nierdzewnej 416 dla dodatkowej wytrzymałości i odporności na zużycie. Pomaga zapewnić pozytywne, spójne wyrzucanie łusek, z mniejszym ryzykiem problemów z niezawodnością spowodowanych zużytym lub złamanym wyrzutnikiem. Zawiera śrubę montażową ze stali nierdzewnej 416.

234 PLN 5 234,00 zł *

Czas dostawy ok. 14-21 dni.
5 szt. w magazynie w USA

Specyfikacja: Caliber: 22 Caliber (.223-.224) Finish: Stainless Steel Make: Ruger Model: Mark III, Mark I, Mark II, 22/45

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Top takeaways

Wyrzutnik wykonany jest z hartowanej stali nierdzewnej 416, co zapewnia dodatkową wytrzymałość i odporność na zużycie.
Produkt pomaga w zapewnieniu pozytywnego i spójnego wyrzucania łusek, zmniejszając ryzyko problemów z niezawodnością.
Pasuje do pistoletów Ruger Mark I, Mark II, Mark III oraz 22/45 i zawiera śrubę montażową ze stali nierdzewnej 416.

Cechy

Kaliber: 22 Caliber (.223-.224) Model: 22/45,Mark I,Mark II,Mark III Rodzaj wykończenia: Stainless Steel Wytwórca: Ruger Waga dostawy: 0,005kg Wysokość wysyłki: 36mm Szerokość wysyłki: 69mm Długość wysyłki: 94mm UPC : 879971007369