Twój koszyk jest pusty.

Koszyk

Pomoc i kontakt

Darmowa standardowa dostawa powyżej 999 zł

Newsletter

Promocje

Ponad 300 000 klientów - dziękujemy!

4,93/5 "Bardzo dobry" (ponad 1400 recenzji)

Ponad 40 000 produktów do polowania i strzelectwa

TALLEY
LIGHT WEIGHT SCOPE MOUNT

810301021846 100031977

Kiedy Każda Uncja Ma Znaczenie; Siła Stali Bez Dodatkowej Wagi

Konstrukcja jednoczęściowa łączy pierścień i bazę w jedną całość. Eliminacja połączenia pierścienia z bazą nie tylko minimalizuje wagę, ale również zapewnia mocniejsze mocowanie. Każda nakrętka pierścienia ma szerokość 5⁄8", z czterema śrubami TORX, aby zapobiec ślizganiu się lub przesuwaniu dużych lunet. Zaprojektowane przez Mela Forbesa z New Ultralight Arms.

SPECS: Aluminium serii 7000, czarny, anodyzowany, matowy wykończenie. Przystosowany do lunet o średnicy 1" (cal), chyba że w kolumnie dopasowań wymieniono inaczej dla lunet o średnicy 30mm. Wysokość od dolnej części pierścienia do górnej części odbiornika: Niski - .400" (10.1mm), Średni - .500" (12.7mm). Wysoki - .640" (16.3mm), Bardzo wysoki - .740" (18.8mm). Przybliżona waga 2.1 oz. (59 g). Niektóre wysokości się różnią, patrz tabela poniżej. Rem. 700 pasuje również do modeli 721/722/725 i 40X. Rem. Model Seven pasuje do odbiorników z czterema otworami na śruby. Savage AccuTrigger pasuje do górnych okrągłych odbiorników centralnego zapłonu z AccuTrigger. Win. 70 pasuje tylko do tylnych otworów o rozstawie .860".

Więcej...

When Every Ounce Counts; The Strength Of Steel Without The Weight

One-piece construction blends the ring and base into a single unit. Eliminating the ring/base joint not only keeps weight to a minimum, it provides a stronger mount. Each ring cap is 5⁄8" wide, with four, TORX screws, to keep large scopes from slipping or shifting. Designed by Mel Forbes of New Ultralight Arms.

SPECS: 7000 series aluminum, black, anodized, matte finish. Accepts 1" dia. scopes, unless otherwise listed in fits column for 30mm dia. scopes. Height from bottom of ring to top of receiver: Low - .400" (10.1mm), Med - .500" (12.7mm). High - .640" (16.3mm), X‑High - .740" (18.8mm). Approx. weight 2.1 oz. (59 g). Some heights vary, see chart below. Rem. 700 also fits 721/722/725 and 40X models. Rem. Model Seven fits receivers with four screw holes. Savage AccuTrigger fits round top centerfire receivers with AccuTrigger. Win. 70 fits .860" rear hole spacing only.

Więcej...

Oceny klientów dla TALLEY REMINGTON 700 LA 30MM MEDIUM 20 MOA SCOPE MOUNTS

Liczba ocen: 13
Od brownells.com: 13
Średnia ocena: 4,8

Perfect (23-01-2014)

Mounting a Leupold 6.5-20x40 on a Savage 12 BJTV w/ thumbhole stock and needed the scope as low as possible. These low extended rings were THE PERFECT solution. Scope is now EXACTLY where I wanted it.

I have 4 sets of Talley rings on 4 separate rifles and could not ask for better rings. Best rings for the dollar out there.

Excellent Product (09-07-2012)

These are the best rings I have found for my custom Mauser rifles. The finish is good enough I do not need to polish and re-finish to make them match the Matte finish of Leupold scopes. They are better than some of the more costly rings I have bought and have built in bases so one less thing to buy.

Delightfully clean 10/22 scope mounts (10-08-2013)

These scope mounts for the Ruger 10/22 are absolutely elegant. Let me share some background info that can help make this relevant to everyone who appreciates 10/22s.

I love 10/22s -- at the moment I have five. I tweak and tune the daylights out of them for both performance and appearance. I'm fond of the contour of the 10/22 receiver and feel Ruger's furnished mount base spoils the lines. For this reason I've made small one-piece bases for my halographic red dots and small two-piece bases for scopes and tube-type red dots -- all starting from Ruger's base.

With the Talley bases, this is no longer necessary. They cover a minimum of the top of the receiver. They're beautifully made and finished. And they hold a scope tightly without marring the finish.

My only wish is that they were also available in a silver finish. They'd look spectacular with my silver Ultradot red dots on my stainless10/22s. I might buy additional black ones and send them off to be reanodized silver. I like them that much.

The BEST I've found for 10/22's. (01-05-2014)

I've installed these rings on 5 or 6 guns now. These are the nicest looking and best working scope mounts I have found for 10/22's if you want a nice traditional look and you're sick of seeing miles of picatinny rail on every gun you own. They are offset so you can reverse each one to get good positioning on the scope tube (as close to the occular and objective lenses as possible while staying away from the erector tube area), they are very well finished, easy to install, line up perfectly and are very sturdy. Order the MEDIUM height for any scope with an objective between 51 and 57 mm. Order LOW height for scopes 50 mm and under. Good shootin'!!

Great Rings! (23-08-2011)

Used this to mount a varmint scope (42mm objective) on my Anschutz 1732 in .22 Hornet. Height was perfect for this application, leaving only a few millimeters of space between the barrel and scope. A bigger objective scope would require higher rings. Easy to install, well made, and rock solid mount and ring combination.

Long-term Test (16-01-2010)

I put a set of these on my Tikka in .338 Winchester magnum several years ago after the "B" brand failed to hold the scope. My hunting load sends a 225 gr bullet out the muzzle at 2900 fps over my Oehler chrono; there is recoil. The Talley lightweights hold the Zeiss 3.5-10X scope absolutely rock solid year after year of hard hunting use in Montana. This is a quality product.

THE BEST - BAR NONE (07-12-2009)

I have sixteen scoped guns and have experience with a number of name brand manufacturers of bases and rings. Tally makes a product that is simple to install and, at least in my case, needed no shimming or adjustments to align the rings which I check with a Sinclair Scope Alignment Tool. So far I have mounted three scopes with Tally mounts with no problem. Nuff said.

GREAT RINGS (10-01-2013)

THEY ARE TRUE, LITE, AND HAVE TORX SCREWS SO THEY CAN BE REMOVED AND TIGHTENED MANY TIMES IF NEEDED.
25#S OF TORQUE IS PLENTY. GREAT PRODUCT.

Great Product (07-10-2009)

I was sort of skeptical about how these would work (no allowance for adjustments), but I heard a good report about Talley, so I gave them a shot. Great fit and finish, and no adjustment needed. In fact, the positional tolerances on these things are so good, that my scope needed less adjustment than with any other type of mounting system I've used lately. Note: For the medium height setup, a 40mm scope is the max. diameter for the Marlin 336.

Perfect fit for short action (07-03-2010)

I mounted these on a Winchester Ranger short action and the fit is perfect. I tried a few other brands, two-piece bases overlapped the action area and one-piece bases did not fit (the ranger action is a bit shorter than a standard short action). They look great on the gun and alignment was right on. No shims required.

Great quality, not very (28-09-2010)

Wanted to replace the medium-height rings that came with my Tikka T3 in 6.5x55 with some that were stronger and lower. I prefer to use a 2-7x32 scope and like to mount it nice and low. The Talley "low" rings, while very strong and well-made, appear to have enough room for a 40mm objective lens scope. They don't appear to be any lower than the factory rings. Other than that (and some embarrassing typos on the packaging), they are great.

A-Bolt LW Scope Mount (20-11-2010)

I used these to mount a 2.5 X 8 Leupold on a 20" Micro Hunter. They're extremely light, but appear to be rugged. The fit is perfect, the scope lined up very square, no need for lapping. I torqued the base screws @ 30 inch/lbs and a touch of blue loctite. The ring screws were evenly torqued @ 22.5. They compliment the clean lines of the little carbine without sacrificing quality. It placed the scopes objective about 1/4" above the barrel, and allowed more than an ample amount of placement for eye relief. I'm sold.

excellant (28-10-2011)

I used these to install a Bushnell Elite scope on my Browning A bolt. The rings fit perfectly and are very secure.

Zobacz 13 dodatkowych opinii na brownells.com

304 559 54 PLN

New

Nr produktu: 100031977
TALLEY REMINGTON 700 LA 30MM MEDIUM 20 MOA SCOPE MOUNTS
Numer części: 740700LM 810301021846 Konstrukcja jednoczęściowa łączy pierścień i bazę w jedną całość. Eliminacja połączenia pierścienia z bazą nie tylko minimalizuje wagę, ale również zapewnia mocniejsze mocowanie. Każda nakrętka pierścienia ma szerokość 5⁄8", z czterema śrubami TORX, aby zapobiec ślizganiu się lub przesuwaniu dużych lunet. Zaprojektowane przez Mela Forbesa z New Ultralight Arms.

Powiadom o dostępności

Niedostępne.

Specyfikacja: Elevation: 20 MOA Finish: Black Height: .500'' Make: Remington Model: 700, 40-X, 721, 722, 725 Scope Tube Diameter: 30mm Style: Direct Mount

TALLEY LIGHT WEIGHT SCOPE MOUNT

Oceny klientów dla TALLEY REMINGTON 700 LA 30MM MEDIUM 20 MOA SCOPE MOUNTS

Top takeaways

Cechy

Szczegóły pozycji

Odpowiedzialny podmiot gospodarczy zgodnie z rozporządzeniem UE

Oceny klientów dla TALLEY REMINGTON 700 LA 30MM MEDIUM 20 MOA SCOPE MOUNTS

Podłącz

Bezpieczne metody płatności

Stowarzyszenia branżowe

Witamy!

TALLEY
LIGHT WEIGHT SCOPE MOUNT