081950077229 Hartowany stalowy spust zapewnia wyraźne 2½ lb. siły nacisku. Nacięcie spustu jest szlifowane powierzchniowo dla prawidłowego kąta i zazębiania. Zawiera sprężynę powrotną o zmniejszonej mocy oraz pełne instrukcje.
Zamówione ponownie
Zaległe, czas dostawy ok. 4-12 tygodnie z magazynu w USA.
Zaległe, czas dostawy ok. 4-12 tygodnie z magazynu w USA.
Hartowany stalowy spust zapewnia wyraźne 2½ lb. siły nacisku. Nacięcie spustu jest szlifowane powierzchniowo dla prawidłowego kąta i zazębiania. Zawiera sprężynę powrotną o zmniejszonej mocy oraz pełne instrukcje.
DANE TECHNICZNE: Stal nierdzewna. Pasuje do Ruger 77/22; 77/17; 77/357; 77/44; 77/50. Może wymagać drobnych poprawek.
Reduces Felt Weight Of Pull
Hardened stainless steel sear provides a crisp 2½ lb. weight of pull. Sear notch is surface ground for correct angle and engagement. Includes reduced power return spring and complete instructions.
SPECS: Stainless steel. Fits Ruger 77/22; 77/17; 77/357; 77/44; 77/50. May require minor fitting.
Cechy
Model:77/22
Typ broni:Ruger
Waga dostawy:0,02kg
Wysokość wysyłki:10mm
Szerokość wysyłki:81mm
Długość wysyłki:104mm
UPC:081950077229
Szczegóły pozycji
Made in USA
US export classification: 0A501.c
Opinie klientów
Oceny klientów (4)
2,8 / 5
Niepolecane
posible saftey issues 29-12-2014
I installed this sear & spring in a new 77/22 wrm. It required filing the safety pad on the trigger to be able to engage the safety. Testing the trigger it broke at 2- to 2 1/4 lbs, and was crisp. The problem I encountered when closing the bolt the sear would not hold the firing pin from going forward and it would uncock the gun. If I closed the bolt very slowly, not in a normal manner it would stay cocked. This looked like a very dangerous condition. The instructions said if this happens, there is not enough tension on the sear. I took out the Timney spring and put the old factory back in . That solved the problem, but raised the trigger to 3 1/2 lbs. The photo shown would make you believe the sear is adjustable, it is not. The next time I would just buy a whole trigger assembly. I will try a Wolf aftermarket sear spring, to improve trigger pull. If this would have worked properly I would have given it 5 stars.
Delikatna rekomendacja
Be careful fitting it 04-06-2011
To fit this you must file the safety pad on the factory trigger. If you go too far, you can not buy a replacement trigger from Ruger, you must either send the rifle back to the factory or put in an aftermarket trigger. I put this sear in a M77/17, but it had a lot of creep. I then tried it in a M77/22, and it gave a nice 2.5 lb pull. I eventually put a Rifle Basix trigger in the M77/17 and it was MUCH easier to install and gave a better pull. I would not buy the Timney sear again and would not recommend it.
Zdecydowanie polecane
Timney 77/22 sear only one worth using 22-05-2011
I am going to sound like a Timney fan again, but after doing trigger work on more than twelve 77/17, 77/22 and 77/22Mag rifles, I will say that the "drop in" sears from other manufacturers ALL were worthless and needed to be stoned to reduce sear engagement and to achieve a good crisp pull. I was so annoyed with these that I was using the OEM parts and stoning the nose of the sear to reduce engagement and winding up with really fine crisp single stage trigger. Then I took a chance and tried the Timney sear which I could see had a set screw to adjust sear engagement. From the factory the trigger still had a bit of creep, so I soaked the sear in WD-40 for two days to break the LocTite 271 (red) bond on the setscrew and then was able to reduce engagement a bit more and the results are just great. You DO still have to stone the safety cam to allow the cam and safety to engage properly so once you install the sear you have a modified gun which is no longer stock and can not be put back in original condition, but that is little problem. You STILL have to drill and tap the front of the trigger hanger for an overtravel screw and I use a 1/8" carbide tip drill bit to cut the rock hard receivers (the stainless as well as the carbon steel receivers are ALL very hard) and then tap 6-32 NF which results in enough thread depth to hold and then use LocTite 271 (red) to hold the setscrew permanently in place. Works just fine but BE CAREFUL in the tapping, back the tap out after cutting every new 90' turn, and use tap lubrication fluid otherwise you will break tap off in the metal trigger hanger. Frankly having to do this on a $600.00 rifle when the Remington 504 for the same money has a match fully adjustable target trigger as OEM equipment is inexcusable on the part of Ruger but the 77/22 guns are really nicely finished and many of us wish to have these in our collections. Now it is possible with a minimum amount of labor and expenditure, to end up with a target trigger pull that is diamond sharp and pulls perhaps 2.5 pounds weight. As we all know, the crispness of the release is more important than the actual weight and a heavy crisp trigger feels lower in weight than a lighter trigger that is jerky and bumpy during release. Again, buy the Timney sear!
Polecane z zastrzeżeniami
Different from photo but works well 26-02-2010
I bought this over the Volquartsen part (which is $10 cheaper) because of the sear engagement set screw shown in the photo. The product I received doesn't have a set screw: not Brownell's fault because the Timney website shows the same picture. Regardless, I installed this on a 77/44 and it gives a much more crisp pull at just over a 2 lb break with the included spring and just over 3 lbs with the factory spring. I had to file the safety cam down a bit. Would have given it 5 stars if the photo was accurate.
Odpowiedzialny podmiot gospodarczy zgodnie z rozporządzeniem UE
Brownells Polska Sp. z o.o.
Armii Krajowej 77
05-071 Sulejówek
Polska
info@brownells.pl
Ostatnio oglądane
Ups! Coś poszło nie tak.
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.
Zwiększ precyzję z RUGER® 77/22® SEAR & SPRING od TIMNEY! 🔧 Wysokiej jakości stalowy spust i sprężyna dla lepszej wydajności.
Elementy te są kontrolowane przez rząd USA i dopuszczone do eksportu tylko do kraju docelowego przeznaczenia do wykorzystania przez ostatecznego odbiorcę lub użytkowników końcowych określonych w niniejszym dokumencie. Nie można ich odsprzedawać, przekazywać ani w inny sposób rozdysponowywać do żadnego innego kraju ani do żadnej innej osoby niż upoważniony odbiorca końcowy lub użytkownik końcowy, w oryginalnej postaci lub po włączeniu do innych przedmiotów, bez uprzedniego uzyskanie zgody od rządu USA lub w inny sposób zatwierdzony przez prawo i przepisy USA.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Elementy te są kontrolowane przez rząd USA i dopuszczone do eksportu tylko do kraju docelowego przeznaczenia do wykorzystania przez ostatecznego odbiorcę lub użytkowników końcowych określonych w niniejszym dokumencie. Nie można ich odsprzedawać, przekazywać ani w inny sposób rozdysponowywać do żadnego innego kraju ani do żadnej innej osoby niż upoważniony odbiorca końcowy lub użytkownik końcowy, w oryginalnej postaci lub po włączeniu do innych przedmiotów, bez uprzedniego uzyskanie zgody od rządu USA lub w inny sposób zatwierdzony przez prawo i przepisy USA.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Wysokiej jakości zamienniki sprężyn do AR-15, wyprodukowane z precyzyjną tolerancją.
Świetne jako części zapasowe lub do montażu karabinu z części zamiennych.
Dostępne pojedynczo lub w zestawach 3-pak, wykonane ze stali chromowo-krzemowej.
Moduł spustu wykonany z hartowanej stali nierdzewnej metodą CNC, zapewnia niezawodność i długą żywotność.
Jednostopniowy design z zewnętrzną regulacją w trzech płaszczyznach, bez potrzeby wyjmowania lufy z osady.
Różne modele pasujące do karabinów Remington 700/40x i Winchester M70, z różnymi funkcjami bezpieczeństwa i siłą spustu.
ATLAS R-ONE to najnowszy dodatek do linii osłon rąk Aero Precision, wykonany z aluminium 6061-T6, zaprojektowany z myślą o lekkości i wytrzymałości.
System mocowania Aero Taper Lock Attachment System (ATLAS) zapewnia równomierny nacisk i unika deformacji osłony ręki podczas instalacji.
Osłony rąk ATLAS są zgodne z górnymi odbiornikami AR-15 spełniającymi standard mil-spec oraz górnymi odbiornikami M4E1 z gwintem.
Wymienialny spust typu drop-in Super Sabra zapewnia dwuetapowe działanie, poprawiając kontrolę i precyzję strzałów.
Regulowany pierwszy etap (3,5-5,5 funta) oraz ustalony drugi etap (2 funty) pozwalają dostosować całkowity ciężar spustu od 5,5 do 7,5 funta.
Łuk Lightning Bow® i wewnętrzne komponenty ze stali narzędziowej zapewniają trwałość i działanie porównywalne do spustu karabinu M4.
Podkładki Double Crush od JP ENTERPRISES automatycznie centrują się i zapewniają równomierny docisk, ułatwiając instalację kompensatora.
Wykonane z czarnej stali węglowej, o wymiarach 5/8"X24 i .750OD, te podkładki są trwałe i niezawodne.
Dzięki oryginalnemu projektowi JP i starannej metalurgii, podkładki te wystarczają na blisko 1,5 obrotu dla idealnego ustawienia. Numer patentu USA 100,041,753.