Cartridge: 223 WSSM (Winchester Super Short Mag), 243 WSSM (Winchester Super Short Mag), 25 WSSM (Winchester Super Short Mag), WSSM FamilyCase Type: FiredNr produktu: 749001636
Uchwyt na łuski L.E. Wilson do karabinów trzyma łuskę podczas przycinania, wiercenia otworów na spłonki, wiercenia szyjek i usuwania zadziorów. Uchwyt na łuski L.E. Wilson zapewnia najwyższą precyzję i jednorodność podczas przycinania Twoich łusek. Unikalny design uchwytu wspiera korpus łuski, podobnie jak komora broni palnej. Uchwyty na łuski są precyzyjnie wykonane dla uzyskania spójnych wyników i powtarzalności. Uchwyty na łuski FIRED są przeznaczone do łusek po strzale. NOWE uchwyty działają z nowymi, nieużywanymi łuskami lub łuskami, które zostały poddane pełnemu wymiarowaniu. Jeśli typ nie jest określony, uchwyt będzie pasował zarówno do łusek po strzale, nowych, szyjkowych lub pełnowymiarowych.
W magazynie
Czas dostawy ok. 14-21 dni. 2 szt. w magazynie w USA
Czas dostawy ok. 14-21 dni. 2 szt. w magazynie w USA
Cartridge: 223 WSSM (Winchester Super Short Mag), 243 WSSM (Winchester Super Short Mag), 25 WSSM (Winchester Super Short Mag), WSSM FamilyCase Type: FiredNr produktu: 749001636
Uchwyt na łuski L.E. Wilson do karabinów trzyma łuskę podczas przycinania, wiercenia otworów na spłonki, wiercenia szyjek i usuwania zadziorów. Uchwyt na łuski L.E. Wilson zapewnia najwyższą precyzję i jednorodność podczas przycinania Twoich łusek. Unikalny design uchwytu wspiera korpus łuski, podobnie jak komora broni palnej. Uchwyty na łuski są precyzyjnie wykonane dla uzyskania spójnych wyników i powtarzalności. Uchwyty na łuski FIRED są przeznaczone do łusek po strzale. NOWE uchwyty działają z nowymi, nieużywanymi łuskami lub łuskami, które zostały poddane pełnemu wymiarowaniu. Jeśli typ nie jest określony, uchwyt będzie pasował zarówno do łusek po strzale, nowych, szyjkowych lub pełnowymiarowych.
The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability. The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.
Top takeaways
Uchwyt L.E. Wilson Rifle Case Holder zapewnia najwyższą dokładność i jednolitość podczas przycinania łusek.
Unikalny projekt wspiera korpus łuski, podobnie jak komora broni palnej, zapewniając konsekwentne wyniki.
Uchwyty są dostępne dla łusek Fired, New, Neck oraz Full Length sized cases, jeśli typ nie jest określony.
Cechy
Nabój:7.62 x 39 mm Russian
Rodzaj łuski:Fired,New
Waga dostawy:0,045kg
Wysokość wysyłki:28mm
Szerokość wysyłki:28mm
Długość wysyłki:52mm
Szczegóły pozycji
Made in USA
Opinie klientów
Oceny klientów (20)
3,8 / 5
Zdecydowanie polecane
Quality 30-04-2018
Typical Wilson quality product. Works great to produce exact length cases.
Polecane z zastrzeżeniami
Limited use with fully sized 308 cases 20-03-2018
Let me say, first, that Wilson products and services are top notch, as is Brownells service. (Wilson trimmers are the most accurate I've ever used. I've trimmed hundreds of rifle cases in various calibers.) This particular case holder works for 243 fully sized (new) and fired brass. It does not work with once fired Lake City or Federal fully sized 308 brass. I used two different Redding presses and standard FL sizing Redding and RCBS dies to check this holder. The sized cases would not extend far enough to be trimmed. I do not have small base dies which reduce the case size to a greater degree to allow more efficient chambering in semi-automatic rifles. I did not use factory new, unfired brass. Based on what I've experienced, I would recommend BOTH case holders to prospective buyers. Rifle chambers vary from Target to Hunting to Military. This is not the fault of the manufacturer or the vendor.
Zdecydowanie polecane
Maybe I do need to be a rocket scientist 08-02-2018
So it's Charles again from previous post. Would like to remove the poor rating I gave product earlier. I have been using the wrong holder I needed new and full length resized holder for my brass, just goes to show that us part time rocket scientist aren't so smart after all. Product is great.
Niepolecane
Frustrated 28-01-2018
Bought the original one about a year ago, waiting for a rifle to get finished finally got my rifle she's a dream by the way. Now comes the not so good, I load 308, 223, 6.8, and various pistol calipers after my first shooting with new rifle cleaned and resized brass case goes all the way through, does not stop on shoulder as others, so I'm thinking I got a bad one it happens returned to brownells for a new one, same thing happening all over again, this time, it's not rocket scientist stick the case in the gage until it stops on shoulder set your cutter to desired length and trim not that hard. So I'm surprised that I got so lucky to get two too many out of spec maybe case gages
Polecane
Does Not Work With Hornady Dies 08-07-2017
Recently bought this case holder to use after full-length resizing with Hornady New Dimension Custom Grade K-31-specific 7.5x55 Swiss dies. Case mouths would not exit the holder, making trimming impossible. However, I measured the shoulder on the resized brass and a fresh GP-11 cartridge. The GP 11 measured .448." The "resized" brass measured .472." I think the blame clearly lies with Hornady's dies, not the Wilson trimmer. Nevertheless, I am leaving this review because I want other shoppers to be aware that if they plan to use the Hornady dies, they will need to buy the trimmer holder for FIRED cases, Wilson item CH7555.
Zdecydowanie polecane
GREAT Trimmer 01-05-2017
FINALLY, a case holder that is accurate, easy to use. and very well made. This case holder, combined with the Stainless Ultimate Trimmer, is a perfect match. For those calibers for which Wilson makes a case holder, this combo will be my trimmer of choice.
Zdecydowanie polecane
Wilson fixed my problem 28-04-2014
I wrote a review on 3/29/14 with complaints about the holder not allowing you to trim if you bump up the neck of the case. I have since been able to contact Wilson and they were nice enough to machine the holder at no cost (outside of shipping it to them). The holder will now work with both cases (standard factory and with the neck bumped up to fit my rifle). I am very happy with the customer service I received and the holder now works great.
Niepolecane
Won't Work for 30-30 with Neck Bumped up 29-03-2014
If you bump the neck up on your 30-30 cartridges to prevent excessive stretching of the brass there isn't enough of the brass extending outside of the holder to trim
Details: Using a Hornady Headspace gauge, I have found my fired brass to "Headspace" at 1.503"
I set my Redding die up to keep my shoulder at 1.501" to prevent excessive stretching of the brass when resizing
I have been trimming my brass to 2.030", but when I changed where my shoulder was, it seems I can no longer use the Wilson Trimmer Case Holder because the end of my brass is still inside the case holder.
Historically, using the generic Redding die settings my shoulder was at 1.485". This seemed to give me enough brass outside of the case holder to trim.
Zdecydowanie polecane
Finest Quality 13-01-2013
I use these trimmer holders in my Sinclair Micrometer Case Trimmer and get superb results. I trim my cases .010 to .015" under SAAMI maximum case length and get amazingly uniform results. The variation is + or - .0005". The jamb fit of the case holds the case in precise alignment. The only downside is the holder grabs the case so snug I have to to tap each trimmed case on a pad to remove it from the holder. Not a big minus when the results I get are so consistent.
Zdecydowanie polecane
Works with my full length and resized 01-11-2012
Works as advertised. If it does not call L.E. they will get you straighted out. It is probably due to a tight chamber or oversized. Case Holders are set up to work with 98% of the chambers that are out there, but if it does not they will get you the correct holder for you.
Zdecydowanie polecane
You will need this holder for new brass 01-11-2012
If you do not want to modify your holder and void your warrenty, you will need this holder.
L.E. will back up everything they make, they added this because your cases sit too deep in the fired holder which does not allow you to trim the case accurately. Bottom Line you need for new brass or full lenght sized brass.
Niepolecane
Buy CH-308W, not this one 30-08-2012
This holder will NOT work with fully re-sized brass.
Zdecydowanie polecane
Drop Proof 31-12-2011
Works great when you don't drop it on a concrete floor.
Zdecydowanie polecane
Need To Revise My Original Rating 31-07-2011
Unlike new Lapua brass, new Norma brass fits very well in this case holder because of its smaller diameter.
Zdecydowanie polecane
Works great! 20-04-2011
Perfect trim jobs from my Wilson trimmer. Just be sure to tap the case into the holder good so it doesn't spin when you go to trim.
Polecane z zastrzeżeniami
nothing special 27-03-2011
soft material,dents easily when dropped to the concrete floor.
Zdecydowanie polecane
Works for both New & Fired Lapua Brass 01-03-2011
If you're using Laupa 6mm BR Norma brass, you won't need to buy the Wilson Trimmer Holder for New Brass. It fits perfect in this one! Just the neck of new Lapua brass protrudes from the Wilson Trimmer Holder for New Brass. I bought both and only use this one.
Niepolecane
Not necessary for new Lapua 6mm BR Brass 18-02-2011
While waiting for my new 6mm BR to arrive I started tooling up and bought both of the Wilson Trimmer Holders for new and fired brass. I'm using only Lapua Brass and I quickly found out that the new brass fits better in the standard Wilson Trimmer Holder.
Polecane
Can be upgraded for Lapua Brass 18-02-2011
You may be able to alter this Holder slightly to avoid having to also buy a New 204 Brass Holder. New Lapua Brass sits too deep inside this Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. But by using a drill press, you can widen the back end of this Holder's hole so that the Adjustment Stop could enter the hole and reach the New Brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's face. I don't know if this will work for Norma brass, as I only use Lapua brass.
Polecane z zastrzeżeniami
You may not need one of these. 18-02-2011
You may not need to buy this New Brass Holder, if you buy the standard Holder (for fired brass) and alter it slightly. New Lapua Brass sits too deep inside the standard Holder, so that the Case Length Trimmer's threaded Adjustment Stop can't reach the case head. Using my drill press, I widened the back end of the Holder's hole so that the Adjustment Stop could enter the hole and reach the new brass case heads. I didn't need to drill very deep, just about 0.1". I used a bit that was a little wider than the Adjustment Stop's head. I don't know if this will work for Norma brass, as I only use Lapua brass.
Odpowiedzialny podmiot gospodarczy zgodnie z rozporządzeniem UE
Brownells Polska Sp. z o.o.
Armii Krajowej 77
05-071 Sulejówek
Polska
info@brownells.pl
Ostatnio oglądane
Ups! Coś poszło nie tak.
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.
Uchwyt na łuski L.E. Wilson 7.62x39mm zapewnia precyzyjne cięcie i rozwiercanie. Idealny do Fired i New cases! 🔧
Uchwyt na łuski L.E. Wilson zapewnia najwyższą dokładność i jednolitość podczas przycinania łusek, wspierając korpus łuski podobnie jak komora broni palnej.
Uchwyty FIRED Case Holders są przeznaczone do łusek po rozmiarowaniu szyjki, a NEW Case Holders współpracują z nowymi, nie strzelanymi łuskami lub łuskami po pełnym rozmiarowaniu.
Jeśli nie określono typu, uchwyt pasuje zarówno do łusek Fired, New, Neck, jak i Full Length sized cases.
Matryce Pro Carbide firmy Lyman są wykonane ze stali nierdzewnej, co zapewnia wytrzymałość i odporność na korozję.
Wysoce polerowane pierścienie z węglika wolframu zmniejszają siłę potrzebną do kalibrowania i zapewniają maksymalną odporność na zużycie.
System tłokowego wypychacza spłonki skutecznie usuwa spłonki z kieszeni spłonki przy każdym użyciu.
Tuleje stalowe hartowane z powłoką z azotku tytanu zwiększają twardość powierzchni i zmniejszają tarcie podczas kalibrowania.
Dostępne w zakresie od 0,185 cala do 0,368 cala z przyrostami co 0,001 cala.
Rozmiar tulei oznaczony jest przez ostatnie trzy cyfry numeru części (#RD76XXX).
Wkładki Sinclair Bullet Comparator wykonane są ze stali nierdzewnej i precyzyjnie obrobione, co eliminuje chwianie się podczas pomiarów.
Umożliwiają dokładne mierzenie odległości od ogiva do podstawy pocisku oraz od ogiva do podstawy łuski, co zapewnia bardziej spójne wyniki.
Zapewniają lepsze odwzorowanie gardzieli komory nabojowej w porównaniu do innych komparatorów z standardowymi otworami wiertniczymi.
Stojak do sprawdzania pocisków Sinclair umożliwia szybkie i dokładne sortowanie pocisków według długości od podstawy do ogiva.
Czarna granitowa podstawa jest idealnie płaska i wystarczająco ciężka, aby pozostać na miejscu na stanowisku do ładowania amunicji.
Wskaźnik zegarowy z dźwignią ułatwia wkładanie i wyjmowanie pocisków do komparatorów, które są sprzedawane osobno i dostępne w różnych kalibrach.
Śruby 6-48 i 8-40 są długie na ¾" i mają różne typy główek: walcowe, owalne oraz Torx.
Zestaw zawiera 12 śrub każdego z sześciu rodzajów, zapewniając szeroki wybór do montażu baz.
Śruby są wykończone czarną oksydą dla zwiększenia trwałości.
Uniwersalny design pasuje do wszystkich popularnych pras, a hartowanie oraz zewnętrzne knurlowanie ułatwiają obsługę i wymianę.
Shellholdery są precyzyjnie wykonane, aby idealnie pasować do łusek kalibrów 243 WSSM i 257 Weatherby Magnum.
Wilson Stainless Micro Trimmer oferuje precyzyjne przycinanie łusek z regulacją co 0,001 cala dzięki wbudowanemu mikrometrowi.
Uchwyt na łuski trzyma je za stożek korpusu, eliminując potrzebę stosowania pilotów podczas przycinania.
Trymer jest kompatybilny z akcesoriami Sinclair International i zamontowany na statywie z zaciskiem Shark Fin, co ułatwia szybkie przycinanie i wymianę łusek.